This slide show shows how to fix the dim/ no lights on the regal dash cluster as well as the dim or no lights on the heater display this works on several car…
Regal Dash Repair.wmv
28
Like
Save
){kind=link}
- Tags:
Dash, REGAL, Repair.wmv
- Categories: Buick
Comments
Write a comment
You must be logged in to post a comment.
works now thx
slightly different problem… ’01 Regal, auto headlights On, Radio and dash lights Off, every time. Manual headlights off, dash and radio lights back On. Any ideas? Thanks.
All 8 Resistors fell off the board when i removed it 😛
Put in youtube Regal dash remove, it takes about 5 minutes to remove it.
From this, I didn’t get how I would remove the part where the odometer is. What tools do I need for that?
Thank you very much for taking the time to help other people with this problem.
one of my resistors are missing completely from HVAC, can i get those or replacement type from RadioC, and which once will i need?
It’s a JOB disassembling the console, but CCP is OK now. I “re-soldered” the old resistors… couldn’t find new ones on net. I have some CONSOLE DIAGRAMS if you want them … KEGLER300@SC.RR.COM … good luck.
I also am having problems with my ‘trac off’ light staying on, along with the ABS light. I made the repairs on my dash for the odometer and driver information center and they worked great! Getting ready to tackle the repair on the Climate Control Panel as well. Please let me know if you have found out a fix regarding the “trac off” light and the “ABS” light staying on. I hate driving without my trac on. Thanks!
Wondering if you havone tackled the Climate Control Panel…. I made the repairs on my odomoeter and driver information center. From what I have read and researched it is a pretty time consuming job removing the Climate Control Panel. Which, would be worth it if this fixes it. Also, if you have made this repair, did you just resolder, or replace resistors? Getting ready to start taking my console apart. Any suggestions appreciated.
Thanks for the post. Just a warning. Be careful not to try and pick off excess solder from the board as this may lift the contact plates from the board. Only use the solder braid as suggested. I think the plates are glued on. My odometer works, but it is dim.
Thanks for this. Did the repair on my wife’s ’02 LS today — well I hired somebody to handle the soldering for me — and it worked great. Total cost: $4 for the resistors plus $15 for the soldering plus about two hours to take it apart, run the parts over to the solder guy, and put it back together. Good stuff.
Many thanks … did DASH last week, now gonna’ tackle the CLIMATE CONTROL.
ALL DIGITAL LIGHTS were out on ’99 Regal LS … Hear it’s a common problem.
If you got any more help videos, they will be WELCOME … THANKS AGAIN
Sorry, but I do not have any experience with that problem, it sounds like it may be a bad calipher or an abs module because it is isolated to your front right brake.
hey man Im having that same problem with my 97.5 buick GS and im still trying to figure out where my problem is.When i get pissed at it and just start driving it makes my front right brake stick and then after a mile or two you can fill it release.Still thats not good for it. if you find out anything hit me on my video page.thanks
All of my lights are out on the dash of my 99 regal, but none of my gauges work either (odometer, rpm and gas). Will this fix that also?
My ’01 regal heater/ac only works on high, which I expect to be due to the same resistors you circled in this video. Do they need to be replaced or just re-soldered? (it says re-solder them but I may replace them anyway) and do you know what the type of resistors needed for the heater? Thanks for this video and all your help!!
You are the greatest, my car finally passed the safety inspection. Have you had a problem with the abs, brake, and trac off light staying on as soon as you put the transm in drive and the lights come on after you drive a couple of feet and they go off when you turn the ignition off? If so can you share your fix. Thanks
THANK YOU!
I did this last year only I just re-soldered what was already there, it over heated and went out again a couple months ago. I’m going to try this, I was just trying to figure out what ohm resister I needed. You rock!
I got everything from Radio Shack
man i’ve been lookn for a ash now i dont have to thanks to u buddie but were do you buy the parts at…..
I can’t believe it worked, but it did. Never thought I could do something like this. My heater control had been replaced by the dealer under extended warranty, and mine looks different inside, but I did see where this flat thing that says 100 on it burned off the board. Who knows? Great video!
I am very glad this helped you solve your problem
Thanks very much for posting this. I was able to fix my odometer/gear indicator in just a few minutes after watching this video. All four factory resistors fell off the board with the slightest touch. After soldering in new ones, my wife is happy once again!
yes desolder before replacing it will give it a good clean surface for the new solder to stick to
Great Video.. im just confused , do u got to desoldering before replacing the resistors right?