Lower Control Arm Replacement 2001 Buick Century GM

Lower Control Arm Replacement 2001 Buick Century GM

Now The Disgruntled Mechanic installs a Lower Control Arm on a GM 2001 Buick Century Custom with the 3.1/ 3100 engine

*****************************************************************
Mailing Address:

The Disgruntled Mechanic
P.O. Box 12
5 E Roosevelt Ave
Elysburg, PA 17824

*****************************************************************

Disclaimer:

BE ADVISED: Any public comment left on THE DISGRUNTLED MECHANIC CHANNEL may get a video response from me rather than a written response. IF YOU ARE NOT COMFORTABLE WITH THIS DO NOT COMMENT!

I am not responsible for any damage anyone does to equipment or themselves from the information contained in the video. If you follow the video and you do stupid shit to you, your equipment, or others it is your fault not the Disgruntled Mechanics! This information is given with the understanding that if you use this information you do so with no liability to the Disgruntled Mechanic or this channel. These videos are for entertainment purposes only! Due to factors beyond the control of the Disgruntled Mechanic, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. the Disgruntled Mechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. the Disgruntled Mechanic recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of the Disgruntled Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not the Disgruntled Mechanic.

12,729
Like
Save


Comments

Murada says:

I have to do this to both the passenger and driverside on my car. I thought that Torx bit would be a pita but I'll take that over having to change out the bushings and the rivited in ball joint been there done that never again. Guess I have to form a battle plan to get that torx bolt off. Why oh why in hell would they use a torx bolt of all things on a suspension piece?

widtrak77 says:

Great video! Was this job done because of a bad ball joint?

kiggsia says:

This video was very helpful to me recently when I did this same job on my 2000 Century. And I too, had a real tough fight with that vertical torx head bolt. I kept soaking it with PB Blaster, and made a press tool with a C-Clamp and a large socket that straddled the torx head. I laid into that with all I had, and it would not break loose. Then I had to face up to how I'd probably have to get a cutting torch, I didn't know if my sawzall would work. But I removed the clamp, squirted more PB Blaster in the rusty, seized bushing and bolt, and tried again, really cranking down hard. Finally I heard that dramatic "CRACK", and I knew that meant I either broke my press tool, or the bolt finally broke loose in the bushing. I was lucky, the tool was OK, and the bolt had finally broke loose! So I too, know the fight these rusty bolts can put up! I really appreciate when mechanics like yourself share experiences, tips, know-how and shortcuts, thanks so much for sharing!

Petia Novakova says:

whats size torx was that you used? thank you

K S says:

I zip tied mine too since the ones that came with the Dorman abs wire harness were bigger than the holes in the GM control arm and I didn't feel like getting the drill out

Big Dog50001 Automotive says:

Zip ties to the rescue! Nice job Mike.

The Snap-On Tool Review says:

I subscribed just because you're "DISGRUNTLED" HAHA I love it!!

Thomas EXOVCDS says:

Wouldn't be fun if it all came apart easy… no? 🙂

buzzsah says:

I gave up working on my van 12-15 years ago when I found a 3rd generation backyard mechanic, besides I got tired of changing the plugs on my astro van.

wyattoneable says:

Solid work Mike. I think you have bigger hammers than Eric. lol Is the jack you used a new tool for you?

Andrew Thompson says:

oo what did you do (not say) during the hour removing the rusty bolt? How to handle things that do not go well is what it's all about. Keep up the good beer!

stuzman says:

Good video Mike and good comments below and annotations in your video about tightening the bolts while the car is on the ground. Take care…

ZIGgassedUP says:

You earn't that beer Mike..

350munro says:

Good job. We don't have weasels in Australia so we use possum piss, it works well but not as well as the fully imported panther piss which I think comes from Russia.
Were you gruntled before you became disgruntled?

super coupe says:

so what happens if you do tighten the bushings with no load on them, cause I've done it in my early years of turning wrenches and never had a come back.

Badgertronix says:

Good job Mike. Always a battle in your climate!

The Plow Guys says:

Good job buddy. I will give ya a call when I need to change mine. I will buy the parts and provide the beer. Helga can cook yeeeehaw!

STEVE ROB REVIEWS says:

Well done with the weasel piss . LOL

Nick Nicu says:

You should never tighten rubber bushings while the suspension is decompressed. You will put the bushings into a bind just as soon as the car will be on the ground. You need to tighten the nuts loosely,lower the car on 2 by 4s or similar,in case there isn't enough clearance otherwise to get to the bolts and tighten them.

Reply to The Snap-On Tool Review Cancel reply